Product ID:INTERSHIELD PRORECO CLEAR FINISH, PRA601/A2/A1
MSDS Date:11/11/1996
FSC:8010
NIIN:00N081117
Kit Part:Y
MSDS Number: CFZQZ

COURTAULDS COATINGS INC

6001 ANTOINE DRIVE
HOUSTON, TX 77091
US

Emergency Phone: 800-854-6813;800-424-9300(CHEMTREC)

Info Phone: 713-684-1563;908-964-2206

Cage: 50411

INTERNATIONAL PAINT INC

HOUSTON, TX 77091 US

Telephone: 713-684-1244

Cage: 028S6

DIETHYLENETETRAMINE AND METHYL ISOBUTYL KETONE DIKETIMINE

CAS: 10595-60-5

Fraction By Weight: 50-100%

OSHA PEL N/K

ACGIH TLV: N/K

2-PENTANONE, 4-METHYL-; (4-METHYLPENTAN-2-ONE) (SARA 313)

CAS: 108-10-1

RTECS: SA9275000

Fraction By Weight: 1-10%

OSHA PEL 100 PPM

ACGIH TLV: 50 PPM; 75 STEL

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

DIETHYLENETRIAMINE

CAS: 111-40-0

RTECS: IE1225000

Fraction By Weight: 1-10%

OSHA PEL 1 PPM

ACGIH TLV: 1 PPM, S

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION: VAPOR HARMFUL. MAY AFFECT
BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS HEADACHE OR NAUSEA.
CAUSES NOSE AND THROAT IRRITATION. EYE CONTACT: CAUSES EYE BURNS.
SKIN CONTACT: CAUSES SKIN BURNS. I NGESTION: MAY BE FATAL AND MAY
CAUSE ORGAN DAMAGE. TOXICOLOGICAL INFORMATION: THERE IS NO DATA ON
(EFTS OF OVEREXPOS)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HEALTH HAZARDS: PRODUCT ITSELF. NOTICE: REPORTS
HAVE ASSOCIATED REPEATED AND PROLONGED OCCUPATIONAL OVEREXPOSURE TO
SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.
INTENTIONAL MISUSE BY DELIB ERATELY CONCENTRATING AND INHALING
CONTENTS MAY BE HARMFUL OR FATAL.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:GENERAL:IN ALL CASES OF DOUBT/WHEN SYMPS PERSIST, SEEK MED
ATTN. NEVER GIVE ANYTHING BY MOUTH TO UNCON PERS. INHAL:REMOVE TO
FRESH AIR. IF DISCOMFORT IS PRESENT/BRTHG IS ABSENT GET MED ATTN
IMMED. EYE S:FLUSH IMMED W/LG AMTS OF WATER FOR @ LST 15 MINS UNTIL
IRRIT SUBSIDES. IF IRRIT PERSISTS, GET MED ATTN. SKIN:FLUSH W/LG
AMTS OF WATER. USE SOAP IF AVAIL. REMOVE SEVERELY CONTAM CLTHG
(INCL (SUPDAT)

Flash Point:104F,40C
Lower Limits:9999
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA AND FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:ISOLATE FROM HEAT, SPKS, ELEC EQUIP &
OPEN FLAME. CLSD CONTRS MAY EXPLODE WHEN EXPOS TO EXTREME HEAT. IN
ABSENCE OF ELEC, WATER SPRAY (FOG NOZZ PREF) (SUPDAT)

Spill Release Procedures:CONTAIN SPILLED LIQUID W/SAND/EARTH. DO NOT
USE COMBUSTIBLE MATERIALS SUCH AS SAWDUST. ABSORB SPILL W/INERT
MATERIAL (E.G. DRY SAND/EARTH), THEN PLACE IN CHEMICAL WASTE
CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:GENERAL:KEEP CONTR CLSD. LOOSEN
CLOSURE CAUTIOUSLY BEFORE OPENING. STORE IN COOL, WELL VENT PLACE
AWAY FROM INCOMPAT MATLS. (SEE SECTION 5)
Other Precautions:KEEP AWAY FROM HEAT, SPARKS AND FLAMES. PROTECT MATL
FROM DIRECT SUNLIGHT. GROUND & BOND CONTRS WHEN TRANSFERRING MATLS.
EMPTY CONTRS MAY RETAIN HAZARDOUS PROPERTIES. FOLLOW ALL MSDS/LABEL
WARNINGS, E VEN AFTER CONTR IS EMPTIED.

Respiratory Protection:USE A RESP APPRVD BY NIOSH AND IN ACCORDANCE
W/29 CFR 1910.134 TO REMOVE PARTICULATES (AND VAPORS IF THERE IS
OVEREXPOSURE TO VAPORS GENERATED DURING PROCESSING OF PRODUCT).
Ventilation:PROVIDE SUFFICIENT VENT, IN VOL & PATTERN, TO:A) KEEP TLV
OF HAZ INGS < LIMS SPECIFIED, B) REMOVE VOLATILES (SUPDAT)
Protective Gloves:CHMICAL RESISTENT GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGS &(SUPDAT)
Other Protective Equipment:ANSI APPRVD EYE WASH & DELUGE SHOWER . AS
NEEDED, USE BODY PROTECTION TO AVOID CONTACT WITH PRODUCT.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRE/EXPLO HAZS: MAY BE USED TO COOL CONTRS. DECOMP & COMBUST PRODS MAY
BE TOXIC. FIRST AID: SHOES) & WASH BEFORE REUSE. IF IRRIT PERSISTS,
GET MED ATTN. INGEST: DO NOT INDUCE VOMIT. KEEP @ REST. GET PROMPT
MED ATTN. VENT: PRODUCED DURING WELD/CUTTING ON SURFS COATED
W/PROD. EYE PROT: FULL LENGTH FACESHIELD .

Boiling Pt:B.P. Text:9999F,5537C
Vapor Density:HVR/AIR
Spec Gravity:0.875
Evaporation Rate & Reference:SLOWER/ETHER
Solubility in Water:NOT KNOWN
Appearance and Odor:LIQUID

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMP AS IN WELDING. FUMES MAY PRODUCE CARBON DIOXIDE
AND CARBON MONOXIDE.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS. DO NOT INCINERATE UNOPENED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.